Characteristics and Availability

Sheet, Coil and Plate Availability | Rod and Bar – Cold Finished Availability
Heat Treat Sheet Alloys & Tempers (Bare and Alclad)
2014 2014A 2024 2219 6061 7075 7475
T4 T4 T3 T31 T4 W W
T6 T6 T4(T-Form) T37 T41 T6 T61
- O-Temper
Special
Inquiry		 T81 T81 T6 T73 T761
- T351 T87 - T76 -
- T361 - - - -
- - T861 - - - -
Note: All T Temper coil is tension leveled through .071″ thick. Tempers T37, T87, T361 & T861 are available in flat sheet only 0.040-0.249 in. Alclad 2014 & 2219 special inquiry below 0.040″.
Heat Treat Sheet Dimensional Capabilities
Gauge (in) Coil Width (in) Flat Sheet Width (in) Flat Sheet Length (in)
From Through Min Max Min Max Min Max
0.008 0.029 12 60 36 60 90 240
0.030 0.130 12 60 36 60 90 240
0.131 0.249 - - 36 62 60 245
Note: All T Temper coil is tension leveled through .071″ thick. Tempers T37, T87, T361 & T861 are available in flat sheet only 0.040-0.249 in. Alclad 2014 & 2219 special inquiry below 0.040″. Heat Treat Plate Alloys & Tempers (Alclad only available for .250 (in))
Heat Treat Plate Alloys & Tempers (Alclad only available for .250 (in))
2014 2014A 2024, 2124 2219 6061 7075, 7175, 7475 7050
T451 T451 T351 T351 T451 W51 W51
T651 T651 T851 T651 T651 T651 T7651
- - T3612 T372 - T7651 T7651
- - T8612 T872 - T7351 -
Note: 2 2024 T361 & T861 and 2219, T37 & T87 only available up to 1.0″ thick. All alloys O and F tempers are available. Ultrasonic Testing available to .5000″ minimum, unless mandated by specification.
Heat Treat Plate Dimensional Capabilities
Thickness Width (in) Length (in)
6xxxx Alloys 2xxx/7xxx Alloys All Alloys
Min Max Min Max Min Max Min Max
0.250 0.270 24 62 24 62 90 221
0.271 0.500 24 66 24 62 90 350
0.501 0.749 24 66 24 66 90 368
0.750 1.500 24 84.5 24 84.5 90 365
1.501 1.999 24 96.5 24 84.5 90 365
2.000 2.999 24 96.5 24 84.5 90 351
3.000 4.000 24 96.5 24 60.5 90 348
4.001 4.500 24 96.5 - - 90 348
4.501 5.000 24 96.5 - - 90 342
5.001 5.500 24 96.5 - - 90 342
5.501 6.000 24 74.0 - - 90 342
6.001 6.500 24 74.0 - - 90 342
6.501 7.000 24 74.0 - - 90 342
7.001 7.500 24 74.0 - - 90 317
7.501 7.750 24 74.0 - - 90 303
7.751 8.000 24 74.0 - - 90 290
8.001 8.500 24 74.0 - - 90 267
Hot Rolled Tread Sheet & Plate – Pattern B 6061-F, O, T4, T6 (ASTM B632)
Thickness Width Lenth
Min Max Min Max
Up to 0.250 (in) 36 (in) 60.5 (in) 72 (in) 245 (in)
Over 0.250″ (in) 36 (in) 60.5 (in) 72 (in) 600 (in)
Note: Gauges available 0.125″, 0.156″, 0.188″, 0.250″, and 0.375″, 0.500″. Non-standard gauges subject to special availability.